Picture |
Part# / Description |
Price |
 |
G-10 BEARING PULLER
(Eaton Print T-9824)
t Countershaft
Front Bearing(#81007) in
the main box
t 900 Series and larger |
$89.95
 |
 |
G-20 BEARING PULLER
(Eaton Print T-10325)
t
Countershaft Rear Bearings (#81008-
81052-81557) in the auxiliary
section.
t
Fuller 8LL,9,10,13 and 15 speed non-
tapered roller bearing aux. (also works
on 613/6613 models) |
$79.95 |
|
 |
G-25 BEARING PULLER
t
Countershaft Rear Bearings (#81012) in
the RT-12510/14610 Auxiliary
section. |
$114.95 |
|
 |
G-28 COUNTERSHAFT PUSHER
t
Attach to case and push c/s thru the
bearing.
t
All countershaft
front bearings in the main
box (all except RT-610 and 613).
t
All countershaft rear bearings in the
auxiliary (all models except
RT-610).
|
$69.00 |
 |
G-29 BEARING PULLER
(Eaton Print # T-22552)
t
Countershaft Rear Bearings (#14366) in
the main box (900 series and
larger). |
$89.50
|
 |
G-32 DOWEL PIN
t
Replacement
Dowel Pins for the G-30
Wrench (3/8" x 1-1/4") |
$3.00 |
 |
G-35 INPUT SHAFT BEARING DRIVER
t
Save time and prevent bearing damage.
t
Works on both 1-3/4" and 2" input Shafts
(will not work on
RT-600/6600 Series). |
$99.50
|
 |
G-38 INPUT SHAFT BEARING PULLER
t
For all 900
Series and larger
transmissions using 1-3/4" or 2" input
shafts (will not work on 600/6600 Series). |
$154.95 |
 |
G-40 AUX. SECTION HANGER
(Eaton Print # T-22823)
t
Aids in removing & installing the Aux.
Section.
t
When attached to a Lift, it holds the Aux.
straight and level for
proper alignment
during installation. |
$59.95
|
 |
TIMING BLOCKS
SUPPORTS & CENTERS COUNTERSHAFTS AND MAINSHAFTS
WHICH AID IN TIMING PROCESS ON ASSEMBLY
tG-50: C/S Rear 900,
1200, and 1800
Series
(Eaton Print #T-22247).
. . . . . . . . . . . . . .
tG-51: C/S Front using one piece
ball
bearing . . . . . . . . . . . . . . . . . . . . .
. . . . . . . .
tG-52: M/S Rear - 900
Series . . . . . . . . .
tG-53: M/S Rear - 1200 Series
. . . . . . . .
tG-54: C/S Ft. & Rear - FRO
. . . . . . . . . . .
tG-55: C/S Front & Rear (7608LL)
. . . . . .
|
$39.95
$39.95
$49.95
$54.95
$42.50
$39.95
|
 |
G-58 TIMING BLOCK
t
Models using the 2 piece Countershaft
Front Bearing (#19551).
t Tool is designed to use with the bearing
inner race installed on the
countershaft.
|
$42.95 |
 |
G-60 SNAP RING INSTALLER
(Eaton Print # T-11938)
t
Installs Snap
Ring (#14291) on the front
Quill of the Output Shaft.
t
Spreads Snap Ring minimum amount
which
results in a tight fit in the groove. |
$49.95 |
|
|
G-70 IMPACT PULLER
t Puller for the Reverse Idler Shafts on
disassembly (1/2-13
Threaded End) |
$49.95
|
|
|
G-71
#8879 BEARING PULLER
G-72 #16780 BEARING
PULLER
t Aux. c/s Front
Bearing Pullers. Thread
onto the G-70 Impact Puller and install
thru the Bearing at an angle. Seat Puller
inside Bearing Cage on Roller ends and
tap out evenly. |
$15.95/ea
|
=
 |
G-90
DRIVE GEAR NUT INSTALLER
(Eaton Print # T-18236)
t
Removes and Installs the 3-1/8" Hex
Drive Gear
Bearing Nut to specified
torque.
t
Accommodates both 1-3/4" and
2" Input
Shafts.
t
3/4" Drive |
$79.95 |
 |
G-110 CENTER BLOCKS (RT610/613)
t
Supports the Right Countershaft (front &
rear)
during Mainshaft & Input Shaft
installation.
t
Aids in timing and Bearing installation on
the
Right Countershaft. |
$49.95 |
 |
G-111 BEARING DRIVER
(Eaton Print # T-10324)
t
For proper installation of various
bearings as shown in Eaton Service
Manuals. |
$89.00
|
|
|
G-112 REAR OIL SEAL DRIVER
t
Installs Rear Oil Seal with the
Bearing
Cover Installed on the Auxiliary.
t Installs the 14337, 19109 or the new style
20807 seals with the cover installed.
t
Less chance of improperly installing seal
because of positive
line up to 900 Series
(2-1/2") and 1200 Series (2-3/4")
Output
Shafts.
t
Used on new generation 11600, 12600,
14600, and 15600
Series.
t Also properly
installs the latest design
Rear Seal (Seal is recessed
1/4" in Rear
Bearing Cover). |
$124.95 |
 |
G-113
BEARING DRIVER (Eaton
Print#1804250)
t
C/S Rear Bearing
(910-9513-12513)
G-230 BEARING DRIVER
t
C/S Front & Rear
FRO 210 Series
G-231
BEARING DRIVER
t
C/S Front & Rear
(7608LL)
|
$84.50
$89.50
$94.50
|
 |
G-115 AUXILIARY REMOVAL AND
INSTALLATION PLATE
t
Provides a safe and efficient means of
removing and installing the auxiliary
section when leaving the Main Box in the
Chassis and reduces the chance
of Bearing damage on
installation.
t
Adapts to Platform of Transmission Floor
Jack and Bolt Auxiliary on
using the two
lower Threaded Removal Holes. Works
on all Aux.
(except RT-610) |
$169.00 |
 |
G-116 SPRING INSTALLER
(Eaton Print # T-11938)
t
Shift Tower Spring Installer (All
Roadrangers)
|
$19.95 |
 |
G-117 DRIVING MAULS
t
Soft Steel Mauls
with Knurled Grip
t
Sizes 2" x 7"
and 1" x 11"
|
$39.50 |
 |
G-119 DRIVELINE ANGLE KIT
t
Checks Driveline Angles without
removing End
Caps.
t
Base Block sets over Bolt Heads directly
on Cap.
|
$49.95 |
 |
G-119A BASE BLOCK ONLY |
$34.95 |
|
 |
G-200H
INTERCHANGEABLE
DRIVING HANDLE
t
Used in conjunction with any G-200
Driving Rings
t
Heat Treated for Long Life
t
Knurled for Positive Grip |
$59.95 |
 |
G-220
TRANSMISSION REBUILD
STAND
t
Extra Heavy Duty Stand
t
25" High
t
24" x 24" Top Shelf
and 28" x 28" Bottom
Shelf
t 5" Colson
Greaseable Ball Bearing
Casters
t
Accommodates all
Models with many
other uses around the shop |
$425.00 |
 |
G-225 MAINSHAFT AND C/S
HOOK
t
For easy removal and installation of
Mainshaft and Countershaft assembles
from the Case. |
$24.95 |
 |
G-235
REAR OIL SEAL INSTALLER
t Installs the New
Rear Oil Seal (#20807)
into the
Rear Bearing Cover (with Cover
Removed from
Auxiliary). |
$34.50 |
 |
G-240 QUILL PULLER & INSTALLER
t No need to scrap and entire Output Shaft
Assembly.
t
Bent or broken Quill can be removed in
minutes.
t Use on old and new Generation Fuller
8LL 13 and 15 speed Transmissions.
t
Supplied with HSS Drill.
t
Quill Installer can be used with a
Hydraulic Press or Hand Maul. |
$94.50 |
 |
G-242 OUTPUT SHAFT BEARING
DRIVER
t
Eliminate Bearing damage from using a
Punch.
t
Faster, easier, cheaper and less
dangerous than using heat.
t
Basic Driver installs inner and outer
Tapered
Roller Bearings onto the 2-3/4"
Tailshaft (1200/1400 Series)
t
Spacer slips into Basic Driver to install
the same bearings onto the
2-1/2"
Tailshaft (900 and 613 Series). |
$89.95
|
 |
G-245
COUNTERSHAFT BEARING
PULLER
t
Front & Rear
(main box) RT610/6610and
RT613/6613
G-246
COUNTERSHAFT BEARING
PULLER
t
Front & Rear
(main box) FRO 210
Series G-249
COUNTERSHAFT BEARING
PULLER
t
Front & Rear (main box) Model 7608LL |
$84.95
$105.00
$84.95 |
 |
G-247 BEARING PULLER
t
Aux. C/S Front & Rear
on FRO 210
Series.
t
Also works on many other Eaton Models
where
the 4302074 (Small) Tapered
Bearing is used.
t
Used with Puller body & bolt from
G-246.
t
Supplied with both SAE & Metric bolts to
protect
threads in C/S rear (center
drilled
bolt heads align the puller bolt). |
$69.00 |
 |
G-247A BEARING
PULLER
t
Aux. C/S Front & Rear
on FRO 210
Series.
t
Also works on many other Eaton Models
where
the 4302074 (Small) Tapered
Bearing is used.
t
Supplied with both SAE & Metric bolts to
protect threads in C/S rear (center
drilled
bolt heads align the puller bolt).
t
Also works on FSO 6406A/8406A
Series M/S Front. |
$99.00 |
 |
G-247B TAPERED
BEARING CUP
PULLER
t
Pulls C/S front cup from pocket
in main
box.
t
Helical 7 Series, FRO, Super 10 & 6
Series.
t
Attach to 1/2-13 Slide Hammer and
place thru
cup at an angle. When
tool is
behind cup, push down below center line
and tap cup out evenly.
|
$24.50 |
 |
G-247C TAPERED
BEARING CUP INSTALLER
t
Installs Aux. Front C/S cup into bore of
main
box. Accommodates small
(4302074) tapered bearing found in FRO
and
many other models.
t
FRO
210 Series
t
Insert on end of G-230 Bearing Driver
(sold separately).
t
See G-257C for large tapered bearing
installer.
|
$29.50 |
 |
G-247D METRIC THREAD ADAPTER
t
Pulls Reverse Idler shaft with threaded
hole in
rear of FRO 210 Series.
t Adapts S.A.E. 1/2-13 thread to M12 x
1.75mm.
|
$19.00 |
 |
G-247E TIMING BLOCK
t
Centers mainshaft rear on
FRO 210
Series.
|
$54.50 |
 |
G-248 YOKE
NUT SOCKET
t
Proto 1" Drive Impact Socket
for the 2-
3/4"
Yoke Nut.
t
O. D. turned down
to 3.813" for Yoke
Clearance.
t
Due to altering the O. D.
there is no
warranty on this Socket. |
$105.00 |
|
 |
G-250 AUX. COUNTERSHAFT
RETAINING TOOL
(Pair)
(Eaton Print # T-65514-S)
t
.100" spacer built into
tool.
t
Outer holes are slotted to accommodate
both large and small bolt patterns.
t
Saves time when measuring for proper
shim on
assembly. Also works on
disassembly.
t
Supplied with 3/8" x 2-1/2"
C/S bolts.
t
Supplied with M12x70
C/S bolts (FRO
Models Only).
G-250A AUX. COUNTERSHAFT
RETAINING TOOL (Pair)
(Eaton Print # T-65514-S-1)
t
.125" spacer built into
tool.
t
Saves time when measuring for proper
shim on
assembly. Also works on
disassembly.
t
Supplied with 3/8" x 2-1/2"
C/S
bolts. |
$109.95/ea |
|
 |
G-251 AUX. COUNTERSHAFT
RETAINING STRAPS (Pair)
(Eaton Print # T-65514-S)
t
Same bolt
pattern as G-250 (slotted
outer holes)
t
Holds Aux. Countershaft in position
during
disassembly and reassembly.
t
Supplied with SAE and Metric bolts.
|
$54.95/pair
|
 |
G-257 BEARING PULLER
t
Aux. C/S Front & Rear on 713/718 &
913/918 Series.
t Also works on many other Eaton Models
where
the 4301851 (Large) Tapered
Bearing is used.
t
Used with Puller body & bolt from
G-246.
t
Supplied with SAE bolts to protect
threads in C/S rear (center
drilled bolt
heads also align the puller bolt). |
$69.00 |
 |
G-257A BEARING
PULLER
t
Aux. C/S Front & Rear
on 713/718 &
913/918 Series.
t
Also works on many other Eaton Models
where
the 4301851 (Large) Tapered
Bearing is used.
t
Supplied with SAE bolts to protect
threads in C/S rear (center
drilled bolt
heads also align the puller bolt).
t
Also works on FSO 6406A/8406A
Series M/S Front. |
$99.00 |
|
|
G-257C TAPERED
BEARING CUP INSTALLER
t
Installs Aux. Front C/S cup into bore of
main box. Accommodates
large
(4301851) tapered bearing found in FRO
and many other models.
t
FRO
210 Series
t
Insert on end of G-230 Bearing Driver
(sold separately).
t
See G-247C for small tapered bearing
installer.
|
$29.50 |
 |
G-259
REAR OIL SEAL DRIVER
t Installs the rear oil seal on FRO 210
Series.
t Greatly reduces chance of improperly
installing seal. |
$89.95 |
 |
G-259A
REAR OIL SEAL DRIVER ADAPTER
t Installs the rear oil seal on FRO 210
Series.
t Greatly reduces chance of improperly
installing seal.
t Used with G-242 or G-112(sold
separately). |
$59.95 |
 |
G-405 BEARING
CUP DRIVER
t
FSO 6406A/8406A Series
t
Input & Output Shaft
t
Used with G-200H
(Sold Separately) |
$44.95 |
 |
G-406
OIL SEAL DRIVER
t
FSO 6406A/8406A Series
t
Side "A" installs Input Shaft Oil Seal
and M/S Front Bearing.
t
Side "B" installs Output Shaft Oil Seal
t
Used with G-200H Handle
(Sold
Separately) |
$49.95 |
 |
G-407
BEARING COVER PLATE
DRIVER ADAPTER
t
FSO 6406A/8406A Series
t
Installs onto side "B" of G-406 to install
Cover Plate
t
Used with G-200H Handle
(Sold
Separately)
t
Used with G-406 Driving Ring & G-200H
Handle
(both sold separately) |
$24.50 |
 |
G-410 BEARING
PULLER
t
FSO 6406A/8406A Series
t
C/S Front
t
Used with Body & Bolt from G-247A
(Sold Separately) |
$69.00 |
 |
G-415 BEARING
DRIVER
t
FSO 6406A/8406A Series
t
M/S & C/S Rear |
$64.95 |
 |
G-420 BEARING
DRIVER
t
FSO 6406A/8406A Series
t
Input Shaft Bearing Driver (with adapter) |
$119.95 |
 |
G-430 Bearing
Puller
t FSO 6406A/8406A Series
t Input Shaft Bearing Puller |
$169.95 |
 |
G-200 BEARING, BUSHING, &
OIL SEAL DRIVER SET
t
For use on most Eaton Transmissions
t
9 Driving Rings (Five of the Driving Rings
are
Reversible) with Interchangeable
Handle
t
Heat Treated Handle for Long Life
t
20 Specific Driving Applications
t Also useful on other
applications where
the sizes match bearing and seal
diameters. When driving bearings be
sure contact is made with both inner and
outer bearing races to avoid damage to
bearings.
t
Convenient Tote/Organizer that is
compact
enough to fit in large toolbox
drawersDriving Applications:
t
8879 Bearing
t 14287 Bearing
t 14366 Bearing
t 16780 Bearing
t 81007 Bearing
t 81008 Bearing
t 81012 Bearing
t 81052 Bearing
t 81505
Bearing
t 81547 Bearing
t 81548 Bearing
t 81557 Bearing
t 4302074 Tapered Bearing (FRO)
t 4302074 Tapered Bearing Cup (FRO)
t 4301851 Tapered Bearing
t 4304080 Bearing (FRO)
t 16516 Bushing
t 16556 Bushing
t 14337 Oil Seal
t 15087 Oil Seal
|
$299.00 |
|
G-600 BEARING PULLER SET
t Puller Set for
207 & 208 Bearings.
t
Puller Set for 1211, 1308 & 1309
Bearings.
t
These 5 Bearings are used throughout 4
& 5 speed transmissions.
t Both Puller Sets (F or G) will work on
either tube & bolt
assy.
t
Will pull bearings on shafts that extend up
to 17".
t Strong Acme Thread Bolt with Heat
Treated
Replaceable Tip.
t All parts are interchangeable - Order
Complete Set(G-600) or either
Tube &
Puller Combination. The Long Tube &
Bolt Assy. will
accommodate shafts
extending from bearing up to 17". The
Short Tube & Bolt will work on shafts
extending up to
8-1/2".
G-600 Complete Set (Shown top
left) . . . . . . .
G-600A Tube & Bolt Assy
(.0"
to 17" Shaft
extending).
. . . . . . . . . . . . . . . . . . . . . .
G-600B Tube & Bolt Assy (.0" to 8-1/2 Shaft
extending).
. . . . . . . . . . . . . . . . . . . . . .
G-600C Bolt
(with tip) - For 17" Tube. . . . . . .
G-600D Bolt (with tip) -
For 8-1/2" Tube . . . . .
G-600E Tip - 17" or 18-1/2"
Bolt. . . . . . . . . . .
G-600F Puller - 207 & 208
Bearings . . . . . . . .
G-600G Puller -
1211-1308-1309 Bearings. . . .
G-600H Ring - Either Size
Puller . . . . . . . . . . |
$349.00
$99.95
$89.95
$44.95
$39.95
$10.50
$69.50
$69.50
$19.75 |
